Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterFast, Reliable Shingle, Tile & Metal Roofing Across Palm Springs
Shingle, tile, and metal roofing in Palm Springs means choosing materials that can actually survive salt air, afternoon squalls, and a concrete-block housing stock that punishes the wrong fastener choices. We install all three roofing types across the village, and we spec them differently here than we would ten miles inland. That’s the difference between a roof that lasts twenty years and one that starts failing in eight. Call (561) 468-6136 and we’ll walk you through what your specific street needs.
Ed Winslow’s name is on the door, and our crews know Palm Springs block by block. We’re not a national chain dispatching a truck from three counties away. We schedule Palm Springs jobs around Palm Springs weather, and we answer the phone when you call.
Why Salt Air Decides Your Roofing Materials in Palm Springs
Palm Springs sits less than two miles from the Lake Worth Lagoon and the Intracoastal Waterway. That proximity is the single biggest factor in how roofing materials age here. Standard galvanized roofing nails and flashing, the kind an inland roofer installs without thinking twice, corrode within 8 to 12 years on the eastern side of the village near Military Trail. We see it on every inspection: nail heads rusted flat, valley flashing paper-thin, drip edges flaking into the gutter. The western edge of Palm Springs gets less of it, but no street is truly immune.
That’s why we carry stainless and hot-dip galvanized hardware on every Palm Springs job and marine-grade underlayment as standard. It costs more up front. It costs dramatically less over a decade. We’ll show you the line item difference in your written quote so you can decide with your eyes open.
On a mid-century CBS ranch off Davis Road, our crew found the original tile roof’s steel valley flashing rusted through and nail heads popping through degraded felt. Textbook Palm Springs salt-air failure. We stripped to the concrete deck, replaced every fastener with stainless steel, installed a high-temp peel-and-stick underlayment rated for HVHZ wind uplift, and re-bedded the barrel tile with polymer-modified mortar. At the end, the homeowner got a wind-mitigation certificate that cut their premium by 22%. That’s what a Palm Springs-specific roof job looks like. It isn’t what a generic roofer from West Palm Beach would have done.
For homeowners anywhere in the village, call (561) 468-6136 for a free in-home measure and a written quote with the coastal-spec line items broken out.
Why Winslow Windows & Doors Is Palm Springs’s Preferred Shingle, Tile & Metal Roofing Company
We’ve been in business since 2011, locally owned and owner-operated by Ed Winslow, with a published address and license number. Palm Springs homeowners don’t have to wonder who’s actually behind the company. It’s Ed. He answers the phone. He stands behind the Done Right Promise: if it’s not done right, we make it right. Not for a season. For a century by the math of that number, and we mean every day of it.
Our Palm Springs customers call back for a second reason: every technician is background-checked and arrives in uniform. You know who’s at your door before the truck pulls up. No subcontractor roulette. No ticket number. A neighbor you can call at 2 a.m., and someone will actually answer.
We also carry the full menu of standing offers without expiration dates: $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the home county, and a permanent 10% discount for seniors and veterans. Upfront pricing. No surprises on the invoice. That’s how a Palm Springs roofing company should operate.
Our Shingle, Tile & Metal Roofing Services in Palm Springs
Tile Roofing: Re-Bed & Re-Point with Marine-Grade Mortar
Concrete barrel tile dominates the 1950s to 1970s CBS ranches that make up most of Palm Springs. The tile itself often survives for decades. What fails is what holds it: the mortar bedding, the fasteners, and the felt underneath. On the eastern side of the village near Military Trail, salt air attacks the steel nails that anchor each tile. We strip to the concrete deck, replace every fastener with stainless, install sealed underlayment rated for our wind zone, and re-bed with polymer-modified mortar that doesn’t crack like the original Portland mix. The result is a roof that looks like the one the house was born with, but performs like a modern system.
Metal Roofing: Standing Seam with Stainless Fasteners
Standing seam metal is the fastest-growing choice in Palm Springs, and for good reason. It sheds wind-driven rain better than any other surface, and the right profile with the right fasteners shrugs off salt air for forty years or more. We spec stainless fasteners and marine-grade clips on every metal roof in the village. Not as an upgrade. As the default. A standing seam roof over a CBS ranch on 10th Avenue North will look clean and modern while actually solving the corrosion problem that killed the original roof.
Shingle Roofing: Salt-Resistant Architectural Shingle
Architectural shingles remain popular on Palm Springs homes that need a straightforward, budget-friendly reroof. We install salt-resistant architectural lines with hot-dip galvanized or stainless fasteners, sealed drip edges, and a full synthetic underlayment. If you’re replacing a shingle roof on a home near the Intracoastal, ask about upgraded ridge venting. Salt air doesn’t just attack metal; it attacks the adhesives that seal shingle tabs, so we use products formulated for coastal exposure.
Roof Repair and Maintenance
Not every Palm Springs roof needs a full replacement. Cracked tiles, rusted flashing, loose ridge caps, and failing pipe boots can all be repaired individually if caught early. We inspect the whole roof, take photos, and give you a written report with line-item pricing. Free second opinions on any written estimate, and $40 off any repair over $200.
This is our Shingle, Tile & Metal Roofing work, and we do it differently in Palm Springs than anywhere else we serve.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Palm Springs
We’re an authorized installer for PGT, CGI, and CWS roofing-adjacent products, and we carry the coastal-spec hardware our Palm Springs jobs demand on our trucks. When your quote specifies a PGT-rated skylight or a CGI-compatible flashing system, we’re not ordering blind from a catalog. We know how those systems install on a CBS block ranch, and we stock the fasteners and sealants that match them. Fast turnaround for Palm Springs homeowners means not waiting on a parts delivery from Orlando.
Common Shingle, Tile & Metal Roofing Problems We See in Palm Springs Homes
- Salt-Air Fastener Failure: Homes east of Military Trail soak in brackish air from the Lake Worth Lagoon. Standard galvanized nails in tile and shingle roofs rust through within 8 to 12 years, loosening tiles and opening nail holes to water. We replace every fastener with stainless or hot-dip galvanized hardware.
- No Sealed Underlayment on Original Cement Tile: Many 1950s to 1970s Palm Springs ranches still have their original tile installed directly over felt or, worse, skip sheathing. Wind-driven rain from summer squalls leaks through cracked tiles into concrete-block walls. The fix is a full strip, sealed underlayment, and re-installation.
- Rusted Valley and Curb Flashing: The vent stacks, skylights, and Florida room roof penetrations built during the jalousie era used low-grade flashing that rusts at the curb. We see active leaks around carports and enclosed porches on nearly every older Palm Springs home we inspect.
- Jalousie-Era Skylight Frames: Skylights framed in the 1960s and 1970s with budget aluminum curbs corrode at the weld points. The glass may be fine. The curb holding it is dust. We rebuild curbs with marine-grade materials before they take the roof deck with them.
What Shingle, Tile & Metal Roofing Costs in Palm Springs
A full tile re-bed and re-point on a typical 1,400-square-foot Palm Springs ranch runs roughly $9,000 to $18,000 when you’re doing it properly with marine-grade mortar, stainless fasteners, and sealed underlayment. A standing seam metal roof of the same footprint typically lands between $14,000 and $24,000, depending on profile and trim complexity. Architectural shingle reroofs run $8,000 to $14,000 for most village homes. Roof repairs are more modest: $350 to $900 for a typical flashing replacement or tile repair, with $40 off any repair over $200.
What moves the price in Palm Springs specifically is the salt-air spec. Stainless fasteners cost more than galvanized. Marine-grade underlayment costs more than standard felt. Polymer-modified mortar costs more than basic Portland. You can buy the inland spec cheaper. Within a decade, you’ll pay for it again in leaks and loose tiles. We quote the coastal spec as standard because your roof lives on the coast. Call (561) 468-6136 and we’ll give you a free in-home measure and written line-item quote.
Florida Pays You Back
The incentives stack in your favor when you upgrade a Palm Springs roof with impact-rated components. My Safe Florida Home offers matching grants up to $10,000 for qualifying wind-mitigation upgrades on qualifying homes. Florida also exempts impact-resistant windows and doors from sales tax. At the federal level, the 25C energy credit can return 30% of the product cost on qualifying units, up to $600 per year. And when a wind-mitigation inspection (typically $75 to $150) verifies your new roof, most homeowners see windstorm-premium credits averaging around 25% on the windstorm portion of their policy.
No guarantees, of course. Programs and carriers set the final numbers. But the direction is consistent: Palm Springs homes that upgrade to impact-rated, wind-mitigated roofing pay less to insure and more to sell. We’ll help you document everything for the inspection.
One comparison worth making: a standing seam metal roof with sealed underlayment is permanent protection. No panels to hang, no shutters to wrestle before a storm, no annual hardware maintenance. Hurricane shutters meet code in many cases, but they only protect when someone puts them up. A properly installed coastal-spec roof protects every hour of every day, whether you’re home or not.
Pricing for Shingle, Tile & Metal Roofing in Palm Springs, FL
Here’s a real range for the village, not a national average. Tile re-bed and re-point: $9,000 to $18,000 for a typical ranch. Standing seam metal: $14,000 to $24,000. Architectural shingle: $8,000 to $14,000. Skylight replacement or curb rebuild: $600 to $2,200 per unit depending on framing. Ridge cap repair: $400 to $800. Valley flashing replacement: $500 to $1,200 per valley.
The line items that push a Palm Springs quote higher than an inland quote are exactly the line items that make the roof survive here: stainless fasteners, marine-grade underlayment, sealed drip edges, and HVHZ-rated accessories. We show every line item in writing before you sign. Free estimate, free second opinion on any competitor’s written quote, and a 10% discount for seniors and veterans. Call (561) 468-6136.
We Also Serve Cities Near Palm Springs
We install shingle, tile, and metal roofing throughout the surrounding Palm Beach County communities including Westgate, West Palm Beach, South Palm Beach, and Boynton Beach. If you’re just outside the village and wondering whether we cover your street, call and ask. Our Palm Springs customers often refer neighbors in adjacent towns, and we’re glad to come out.
Serving Palm Springs, FL - Our Local Coverage Area
We’re based in the Palm Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Shingle, Tile & Metal Roofing in Palm Springs
The east side of Palm Springs sits closer to the Lake Worth Lagoon and Intracoastal Waterway, so salt-laden air from the prevailing coastal breeze deposits more corrosive salt on exposed metal. Standard galvanized nails fail in 8 to 12 years there, while the western edge of the village sees slower corrosion. We use stainless or hot-dip galvanized fasteners on every Palm Springs roof regardless of street. Call (561) 468-6136 for an inspection if you’re seeing rust streaks or loose tiles.
Palm Springs falls within Palm Beach County’s wind-borne debris region, so roofing systems must meet Florida Building Code wind-uplift standards for our zone. Many manufacturers test their systems to Miami-Dade NOA or Florida Product Approval standards, and we match design pressures to the opening and deck. We won’t install a system rated below what your specific roof deck and wind zone require. An in-home measure tells us exactly what applies to your house.
Yes. The roof and the windows are separate scopes. But if you’re planning both, doing them together lets us coordinate the flashing and curb work around skylights, Florida rooms, and window openings in one pass. Jalousie windows are a known weak point in Palm Springs homes, and if you replace them later, we can spec the roof penetrations to accommodate the new openings from the start. Call (561) 468-6136 and we’ll walk you through sequencing.
Because Palm Springs is a coastal village, not an inland town. The spec we install here includes stainless fasteners, marine-grade underlayment, sealed drip edges, and polymer-modified mortar rated for salt exposure. An inland roofer can use standard galvanized and basic felt for less money. Within a decade, that cheaper roof on a Palm Springs home will start losing tiles and leaking. The coastal spec costs more up front and far less over time. We’ll show you both numbers in writing so you can compare honestly. Free estimate: (561) 468-6136.
It should, assuming the system is installed with sealed underlayment and verified fasteners that meet our wind-uplift requirements. The wind-mitigation inspector confirms the roof deck attachment, underlayment, and roof covering. You’ll likely see a meaningful credit on the windstorm portion of your premium. We provide documentation for every installation, and we’ll point you to the inspection. Call (561) 468-6136 to get started with a free measure.
Contact Winslow Windows & Doors for Shingle, Tile & Metal Roofing in Palm Springs
If your Palm Springs roof is showing rust, loose tiles, cracked mortar, or water stains on the ceiling, call (561) 468-6136 today. We’ll come out, inspect honestly, and give you a written quote with the coastal-spec line items clearly listed. No pressure. No vague numbers. Ed’s name is on the door, and the Done Right Promise is on every roof we install. The one down the road is the one to call.
Written by Ed Winslow, Owner at Winslow Windows & Doors, serving Palm Springs and surrounding Palm Beach County communities since 2011.
Six Reasons Homeowners Choose Winslow Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.